Forum Post: TMS320F28335: Supplied 9V instead of 5V-Board not working--- Want...
Part Number: TMS320F28335 Dear friends, I am ganeshan.I am using the Delfino board with TMS320F28335 . I tried working on the serial communication using SCI_A on the board using Matlab Simulink. While...
View ArticleForum Post: RE: MSP430I2040: BOR and SVS behavior – Power Up
Hi Kuerbis, before I answer your first question, let me answer your second. Please have a look at picture below. As you can see, BOR is generated by ORing of BORH and SVSL. That means as soon as both...
View ArticleForum Post: RE: TM4C1294NCPDT: UARTCharPut hangs as though UART is not enabled
Hi Charles, I spent time commenting out plenty of things that happen prior to my UARTCharPut() calls to see if I can remove my sysctrldelay call but I have not been successful. I might put the...
View ArticleForum Post: RE: MSP-EXP430FR5994: Comparing atan2 with QMath _Qatan2 and...
Hi Larry, I will take a look at your code as well as the APIs and then feedback you if any idea.
View ArticleForum Post: RE: CCS/MSP430FR2311: MSP430FR2300
Hi Suma, Did you create a wrong thread? Any more information could you provide for your question?
View ArticleForum Post: RE: TMS320F28377D: SDRAM and FPGA supported at the same time
Hi, Another issue about the size of SDRAM and FPGA. Customer would like to connect to 4M words SDRAM and FPGA (connected to 64K words RAM). EM1A13, EM1A14, EM1A15 and EM1A16 will be used. But these...
View ArticleForum Post: RM48L952: RM48L952 bootloader is not jumping to application code...
Part Number: RM48L952 Hi, We facing problem with bootloader is not jumping to application code after writing APPLICATION_CODE code Flash memory. Description: 1) Bootloader code is stored in the FLASH1...
View ArticleForum Post: RE: CCS/MSP430FR2311: msp430fr2311
Hello Suma, there is e.g. this E2E thread, which is dealing with the topic how to measure current values, in case you need still some further information. e2e.ti.com/.../102532 In your case, you do not...
View ArticleForum Post: Compiler/TMS320F28335: *.out to *.hex with 8 romwidth
Part Number: TMS320F28335 Tool/software: TI C/C++ Compiler Hi, We'd like to convert *.out to *.hex with 8 romwidth, in only one hex file, instead of two (one *.hex,, one *.i01). Is there any way?...
View ArticleForum Post: RE: TMS320F28379D: Software watchpoint
Hi, in this week I will investigate this problem more and then I answer. Best regards, Łukasz B.
View ArticleForum Post: TMS320F28069M: Motorware lab13a stops holding position after a while
Part Number: TMS320F28069M I'm running the lab13a with finely tuned bandwidth. In the beginning the motor shaft is stiff and holding position (I can barely move it with my fingers) but after some time...
View ArticleForum Post: RE: RTOS/MSP430F5529: TI-RTOS, two spi(one master one slave)...
hi Tooma I'm sorry I just got back to you because of time difference . You're right. Two spi can use different DMA channels to resolving the SPI_transfer() funtion conflicts, but 5529 only three DMA...
View ArticleForum Post: RE: TMS320F28335: Supplied 9V instead of 5V-Board not working---...
Ganeshan, It is best not to assume, or hope things just work when powering a pcb externally. Be sure that you understand the datasheet requirements and limitations. That being said, you can use a...
View ArticleForum Post: RE: RTOS/TM4C1294NCPDT: TCP Echo example on Custom board
[quote user="digvijay khambe"]While checking for ARP i disconnected PC from LAN [/quote] You are using a cross over Ethernet cable or have a switch connected when doing this? It will not work to plug a...
View ArticleForum Post: RE: CCS/TMS320F28377S: difference b/w dsp280x and f28377s
The F28377S is a much newer device, so naturally you will see much better computational performance, and more and improved peripherals. Comparing the front page of the two data sheets will give you a...
View ArticleForum Post: RE: LAUNCHXL-F28377S: ePWM Pins are HIGH at startup
Hi Manoj, Thank you very much for looking into this. There's just one more thing that confuses me right now. I just erased the entire flash using Uniflash and made a successful blank check, so the...
View ArticleForum Post: MSP432P401R: I want to write assembly codes for the above...
Part Number: MSP432P401R I always write assembly codes for MSP430 as they are very specific and helps me to debug from register to register and control data flow. I want to do the same for MSP432P401r...
View Article
