Forum Post: RE: EK-TM4C123GXL rtos gpiointerrupt example get stuck and goes...
Hello Embedded_career,Can you check if the SYSCTL.RCGCGPIO register bit corresponding to Port G is set before the GPIOPinTypeGPIOOutput is called?The bit position in the register would be bit-6 in the...
View ArticleForum Post: RE: TM4C129X Custom Bootloader
Hello Gaurav,The TM4C129 memory is 8KB sector size but then it spans over 2 banks making it 16KB (0x4000). Since you tried to erase 0x2000 onwards the entire region from 0x0 to 0x3FFC is erased. Hence...
View ArticleForum Post: RE: EK-TM4C1294XL-CCS download speed slow
Put a hold on that last post. I now have information that it may be a problem at my end. Will try on the home computer and report back.
View ArticleForum Post: RE: Error during build
Hi Gautam,Does this mean, an array this big cannot be used with C2000? I wish to eventually do a 512 point FFT on this data. Will the RAM size become a constraint for my application?ThanksNisha
View ArticleForum Post: RE: Using the multi_tx.c peripheral on the Launchpad (TM4C123GXL)
Hello Brian,I have cleaned up the CCS project for compilation in my best understanding of the code you have posted.(Please visit the site to view this file)RegardsAmit
View ArticleForum Post: RE: system reset through instruction
Hi Girish,If you are looking for an instruction to reset your device, one popular thing I've seen people do is to simply write to the watchdog control register WDTCTL with an incorrect password....
View ArticleForum Post: RE: 28069 SPI to external FLASH - SPISTEA or GPIO as Chip Select
Brent,You can most definitely use the SPISTEA line as the Chip select. The reason many people use a GPIO is if they have multiple slaves connected to the same SPI. If you are only connecting SPIA to...
View ArticleForum Post: RE: CCSv6 - MSP430 - GCC 4.8 - #include msp430.h does not work
Hi Eric,Thanks so much for the very detailed feedback - sorry that you had to run into this issue. I'll report this as an improvement that needs to be made on the header files.Regards,Katie
View ArticleForum Post: Embedded Workbench Simulator USCI_A0_VECTOR Interrupts being...
I've only recently read about the C-spy debug macros. Using code that communicates and runs as expected on FR5969 using the USCI_A0, I'm trying to generate interrupts to simulate incoming bytes while...
View ArticleForum Post: RE: Creating a custom BSL for firmware update
Hi Roy,One thing that may help is looking at this app note called MSP-BOOT: www.ti.com/lit/pdf/slaa600 It shows a method for making a main memory bootloader with optional dual-image support like you...
View ArticleForum Post: RE: What causes TZ2 to trigger except Fault/OCTW (BOOSTDRV8301)
Great to hear!The 10A rating is for RMS current out of each half-bridge simultaneously. We basically took a fairly large motor and saw thermally what we could drive continuously at ambient temp. before...
View ArticleForum Post: RE: to receive data from remote sensor using xbee and glow an led...
How do i open the file?
View ArticleForum Post: RE: MSP-EXP430F5529LP not recognized in CCS "No USB FET was found"
Arthi,A colleague of mine just attended a conference where he received another MSP-EXP430F5529LP board. I plugged it in, the light came on, the drivers installed correctly, and the demo worked without...
View ArticleForum Post: RE: InstaSPIN GUI and CCS hung up while connecting target
Hi Kelly, Yes, this is what I was looking for. The last line of log file has a crash log file that I was hoping that you could attach as well. ....0x000007B8 161533 1 ERT E: A crash occurred - dump...
View ArticleForum Post: RE: Windows 7-64 USB driver question
I have looked for newer drivers but have not found where I can download the drivers for the older M3 9D96 CPU's.
View ArticleForum Post: RE: Looking for native assembly language sqrt() equivalent to...
Hi Chuck,Ok that's good. If you are happy with the performane you can stop obviously.If not you could try inlining the sqrtf function. The optimization I referenced in the TI compiler would be much...
View ArticleClik here to view.
Forum Post: RE: Stellaris Virtual Serial Port driver error in Labview
Hi Mitch,I am so glad and relieved, that I can press the green "Yes" button and accept the resolution of the problemThanks very much to you and everyone else involved. Much appreciate it.Best RegardsJan
View ArticleForum Post: RE: using MAC on Concerto
Yes, who ever is making the end product that can be hooked up into a Ethernet network will have to do it. Best RegardsSantosh
View ArticleForum Post: RE: 3 Bugs Found in motorware_1_01_00_11
Saed,On #3 I don't think there is an error.There may be code missing to do what YOU want to do (add more ADC SOC channels), but what we have done is fine.The SOCs are all all initialized in the...
View ArticleForum Post: RE: UART_ECHO - Stellaris 3S9D96 Problem
[quote user="Leonardo Saavedra"]I don´t know how to assign the pins.[/quote]I think you can check this at the DK-LM3S9D86 User's manual. I don't have a DK-LM3S9D96 to verify.-kel
View Article