Forum Post: RE: TMS320F28335 codes works in RAM but not FLASH
Hello Lei Gu,I am sorry that I can not test the firmware because I don't have the hardware.I usually plays with Sensorless firmware for F28027 (HVACI) and they works just fine in flash.Is there any...
View ArticleForum Post: RE: Unlock of NMI/JTAG pins: Unspecified behaviour?
The issue our group sees upon multiple (past) LX4F devices is PF0's apparent tendency to accept our SW config as, "Analog Comparator Output" - with absolutely "NO" unlock code in play. This comparator...
View ArticleForum Post: RE: Start and low speed with load problem
I've checked, compiler version 6.2.4, CCS version 5.3.
View ArticleForum Post: RE: ATANPUF32 RaH, RbH
It's for TMS320F28377DWhere can I download the compiler version 6.2.4? I use CodeComposerStudio version 5.
View ArticleForum Post: RE: Pin discrepancies between documentation for Tiva Launchpad,...
You should note too the presence of (famed) 0-ohm resistors on your board - which "join" PB6 & PB7 to PD0 & PD1. It may not be possible to cleanly, "exit" each/every pin of that 4 pin cluster -...
View ArticleForum Post: RE: know about the how to solve the proble in my ez430 chronous...
hey Vaibhav,check out this video demonstration of setting s for different modes in Ti chronos watch.
View ArticleForum Post: RE: How can I implement interrupt for receiving single byte from...
Hi, everyone,I had already tested it as you mentioned.You says that UARTFIFODisable function is available.I'll retry with UARTFIFODisable function.I really appreciate for your advices.
View ArticleClik here to view.
Forum Post: RE: RE: General Purpose GUI
Dear Dorbrin May I ask you some question about GUI composer?Now I use TMS320F28335 for a motor control experiment. During the debug process, I need to observe 8 variables at same time. Originally...
View ArticleForum Post: RE: Mcu reset after timer overflow interrupt
Thank you JMG. Ohh god, for a long time, I am literally abusing the WDT . I should improve my coding skills. Thank you.
View ArticleForum Post: RE: query about usaing timer as counter
hey karan,If u have got your answer can u please close this thread by checking verified answer please.
View ArticleForum Post: RE: Startup init routine hangs
Yes, definitely it is the watchdog which intervenes. I originally took for granted the start up routine took in account the fact that the bigger the size of variable the longer it takes and set the...
View ArticleForum Post: RE: motor ID problem
Yes this one is giving me alot of trouble. I set the Ls to 0.000050, and the motor run OK, but only after I give it a little push at the beginning. And the problem with the RPM persists, after it...
View ArticleForum Post: RE: MSP430 i2c interrupt
If initially set the MSP430 i2c to slave (receive signal) and connect to other device which is master (sending signal). How to enable the interrupt process when master sending signal to slave. If the...
View ArticleClik here to view.
Forum Post: RE: non-sinusoidal phase current
Hi ChrisThese are the answers:1. Are you sure your parameters are correct? It is a very large flux and a very small Ls.Using the Isc equation:Isc= Flux(V.s) / Ls (H) = 0.019/0.000165= 115.15 AIsc=...
View ArticleForum Post: RE: BSL_Scripter MASS_ERASE and RX_PASSWORD
Thanks, Leo!But I receive 0x07 only in response to mass_erase - but it is not that bad I suppose, because instead of mass_erase for usb devices we should use rx_password erase_pass.txt (as far as I...
View ArticleForum Post: RE: USB stack re initialization issue
Hi Rajasekhar,[quote]To avoid this situation we are planning to stop the USB functionality before Relay switching and completely fresh USB start with enumeration after this.[/quote]You may drop the bus...
View ArticleForum Post: RE: Debug lab01 with LaunchpadXL
Hello Bruno,If you use LaunchPad XL F28027F, indeed you need to select the motorware firmware under \boostxldrv8301_revB folder.The main file is the same (proj_lab0xx.c) but the hal module (hal.c,...
View ArticleForum Post: RE: motorware_1_01_00_12 CAN support
Hi Chris, Thank you very much for your answer.Now i am trying to port the CAN Bus driver in Motorware_12.i think it is possible.just copy and paste something ;-).I have an inoffiziell version from...
View ArticleForum Post: RE: MSP430Flasher problem with output file name length when...
Just to wrap this up:This bug is fixed as of MSP430 Flasher v1.3.0.Best Regards,Robert
View ArticleForum Post: RE: THREE PHASE ENERGY METER BASED MSP430F47197
Hi, Do you mean this below? http://www.ti.com/tool/tidm-threephasesom It says there that it has a standard MSP430 FET connection. So, use a MSP430 USB Debugging Interface. See, below....
View Article