Clik here to view.
Forum Post: F28035 PWM modules
Hi, I want to make a waveform like thisHow to use the pwm module to make it?Thanks.
View ArticleForum Post: RE: TMS320F28335 NOT CONNECTING
Hello,Here the SPI doc that you mentioned.(Please visit the site to view this file)Good luck!Best regards,Maria
View ArticleForum Post: RE: ft800 interfacing with tiva
Hello Mithesh,The code does not tell how the command sequence is generated for ft800. Secondly the issue I believe is that the CS is toggling after every byte sent. That is the default behavior of SSI....
View ArticleForum Post: RE: MPU-6050 sensor with Simulink on F28335
Dear Juraj,Thank you very much for the quick reply. Indeed, most of the available information on the internet is tailored for the Arduino (we got the sensor to work on the Arduino, but we want to work...
View ArticleForum Post: Uart Bootloader RM48
Hi,I have download a bootloader software to RM48L952 and i have a problem that when i download a new software viaJTAG (not using the bootloader) and i disconnect the JTAG the application didnt runDoron
View ArticleForum Post: RE: I can't get USB0CLK working (newbie)
Which MSP are you using? There are >400 different MSPs, and pin mappings are device specific. From the usage of UCB0 and IE2 and P1SEL2, I see it must be a 2x family device, but beyond that I can...
View ArticleForum Post: RE: Troubles with SPI clock on MSP430G2955 (and MSP430G2553)
You might be using the wrong polarity or phase. If so, then communication is fragile and only works due to line capacitance and driver delays. On higher speeds, the timings are narrower and...
View ArticleForum Post: RE: the SPI interface between MSP430F5529 and ADS1298
“Doesn’t work” is highly ambiguous. What doesn’t work? Don’t you get any response? Or a wrong one? Is there a signal on the SPI wires at all? Did you check with a scope? What does a logic analyzer...
View ArticleForum Post: RE: HOW CREATE A SECONDARY INTERRUPT TABLE
The secondary interrupt table is the very same as the primary one – only the address it is read from is changed to the end of ram instead of end of lower 64k. So it makes no difference – it still...
View ArticleForum Post: RE: Timer
The ISR will only be called if 1) the IFG bit flags the event, and 2) the IE bit allows the interrupt and 3) GIE is set. So if you don’t set an IE bit of an interrupt you don’t want, then you won’t get...
View ArticleForum Post: RE: Forum usage
Sorry, I have to disagree.If someone comes here to search for help, he has to understand that he cannot demand help from people who are not paid. And he cannot expect to be helped in his native...
View ArticleForum Post: RE: [Help] Read/Write Variable in Flash Memory
This only shows how many people are starting a new thread for already answered questions instead of using the forum search first. I agree that it is frustrating to search through a heap of ‘empty’...
View ArticleForum Post: RE: How to control ePWM output speed?
Hello David,I had a doubt in your DAC sample example:1. What is the significane of the MACRO "scale" in the 256 points lookup table? Does this control the voltage level of the output PWM wave? What is...
View ArticleForum Post: RE: assembly compile fails, no error output
Is there by the way a maximum of commented lines allowed between ASM code? I removed some commented lines and now the asm file suddenly builds... !?
View ArticleForum Post: RE: Generate 12.5Mbps signal with F28335
Thank you so much Devin. Your support is really appreciated. I wil reconsider my design according to your information.Thank you!
View ArticleForum Post: RE: ButtonsPoll()
Hello Vikas,The prototype can be found in drivers for every board examples. There is no tutorial document as...
View ArticleForum Post: RE: ADC Tigger source
Hello Ahmed,The trigger source cannot be OR-ed for the same sample sequencer.RegardsAmit
View ArticleClik here to view.
Forum Post: I think TI's Crystal cap. calcs for the TM4C129X are in error
This discussion has part academic value and part practical value. I believe TI have made an error in their formula for CL, the load capacitance specified by the crystal manufacturer. TI went to...
View ArticleForum Post: RE: ft800 interfacing with tiva
Hello,You can take an example of connectEVE for easy understanding.Data format and all I have used in arduino and it worked there and I have replicated here so I don't think it might show issue...
View ArticleForum Post: RE: SRCR2 or SRCR0 for USB peripheral reset on F28M35H52
Trey German,I thank you for your answer,Best Regards,JDM
View Article