Forum Post: RE: how can i create my own RTSC PACKAGES (SYSBIOS 6_37)...
Lei, please write the part number on the "Device name". If you scroll down you should be able to find TMS320F28335. Also, which version of XDCtools do you have?
View ArticleForum Post: RE: How long should it take to wake up from deep sleep?
Hello Rob,Can you post the code, that would help understand the issue better,RegardsAmit
View ArticleForum Post: RE: How to interface EEPROM with LM3S8971
Hi Radhika,What type of EEPROM device and how do you intend to interface it with LM3S?RegardsAmit
View ArticleForum Post: RE: RM48 and eMMC 4.3 and Above
Thanks Anthony,I also had a similar idea of gating the SIMO output using a tri-state buffer while connecting the 1bit data line to the SOMI pin.I think this is the solution I will attempt, however I...
View ArticleClik here to view.
Forum Post: MSP430 Internal OpAmp bandwidth
Hello. The question is about bandwidth of internal operational amplifier of MSP430 family. As I’ve realized from datasheets on devices, that contains OpAmp inside, the maximum frequency of...
View ArticleForum Post: RE: DHCP failing in debug mode
I would like to add that I think the DHCP issue is one symptom of a bigger issue. In my app I use a static IP and it does not run correctly under the debugger either.Please help!
View ArticleForum Post: RE: MSP430F5659 backup battery circuit
[quote user="Jens-Michael Gross"]And things like the backup circuit are published as whitepapers or application notes. (of which TI publishes way more than any other company, because they too apply to...
View ArticleForum Post: RE: MSP430F5529 LCD module
Thank you very much for your inputs. Its really helpful.Yes, I am looking for charecter displays. I see most of them are around 7cm long.Are there any products that I can find with in 5cms long, but...
View ArticleForum Post: RE: SCI TX interrupt in Hercules
[quote user="Umesh Thirunavukkarasu1"]Hi all,I am working RM42X LaunchPad. I configured SCI Driver enable, VIM0-31 13th Interrupt LIN Level0, and enabled TX interrupt in the SCI...
View ArticleForum Post: RE: controlCARD connection problem
Hi Roman,Firstly, the F28M35x controlCARD has an on-card FT2232H-based xds100v2 emulator. Therefore your target configuration is correct. (xds100v2 + F28M35H52C1)I think the key thing to note here is...
View ArticleClik here to view.
Forum Post: RE: Need explanation with the working of timer to start the ADC...
I understood the working in this way,Timer counting section from 0 to 9999It counts from 0 to 9997(TACCR1) and then there comes the out_mod=3 that makes the OUT1 signal =1 and then OUT1 signal goes to...
View ArticleClik here to view.
Forum Post: RE: TPS65381 DIAG_OUT is always zero
On power up, DIAG_OUT is initially in high impedance state, but is sharply pulled low ~40ms after power-up (cold start), and ~2-3ms after receiving init commands from Hercules.When Hercules is...
View ArticleClik here to view.
Forum Post: RE: Having problem TMDSDCDCLEDKIT
Hello,If you click on Example GUI what happens?Nonetheless, you should be able to access the GUI from the controlSUITE directory:\controlSUITE\development_kits\Lighting_DCDC_v2.2\~GUI\The QSG PDF and...
View ArticleForum Post: RE: Incremental encoder + eZdsp F28335
Thanks for the reply Mitja!I did some research and indeed, as you said, for my application I need the absolute rotor position so I need an absolute position encoder. Can I also use the AM26LV32...
View ArticleForum Post: RE: msp430 f5529 clock configuration
hi mike and thanx for the quick response!i did open that example but it looks a bit complicated, i should say im new to microcontrollers.maybe if i tell you what i am trying to acomplished you will...
View ArticleForum Post: RE: RE: Blinky LED example - stuck in _memoryInit_ loop
Thanks Anthony,They devices are mounted to our pre-production hardware.Thanks for your advices.CheersStomp!.
View ArticleForum Post: RE: How to set up M3 as Flash Standalone?
Hi Santosh,No, you have not answered the question. The link to ttp://processors.wiki.ti.com/index.php/Project_Build_Configurations is worthless, and I have read section 6 of the spruh22f.pdf, as I...
View ArticleForum Post: RE: Hi there! Has anybody seen this FLASH problem, or knows what...
Marek,I am sympathetic to your plight :)For what it is worth, when I installed CCS3.3 on the Win7 machine I received a while back, I edited CCS3.3's shortcut to allow the program to "Run as Admin" and...
View ArticleForum Post: RE: Issue with MSP430G2443 Reset
[quote user="abhishek Sabnis"]making system freq = 1MHz will help ?[/quote]Yes. Apparently you missed my answer having other considerations
View ArticleForum Post: MSP430 and CC2560 Medical Project
Hi my university's research team is building a medical bracelet that wraps around your wrist and uses spectroscopy to determine levels of chemicals in your blood. I am going to have a ccd chip that...
View Article