Forum Post: MCU freezing when 2nd Virtual Serial port is not connected
I've been using the MSP430F5529 for a USB design. I have a 2nd virtual COM port setup as the debug port. If I don't have a connection open to that 2nd virtual COM port the program will block until...
View ArticleForum Post: RE: Oscillator fail-safe operation
Your code requires that there are two crystals, both between 3 and 16MHz. Why????????????????If one of them or both of them are not working properly, there will be an OFIFG.
View ArticleForum Post: RE: Error initializing emulator: No USB FET was found
Hi David,From http://processors.wiki.ti.com/index.php/Linux_Host_Support#Not-Supported Not-Supported MSP430: eZ430 emulators, Legacy MSP430 LaunchPads & Experimenter's Boards with eZ430 based...
View ArticleForum Post: RE: CortexR4: Trouble Writing Register REG_AHB_DOWNLOAD: No...
Hi,I get the same bunch of errors.But everything is working ok otherwise.I'm using TMS570LS1227 with J-Link EDU and CSS 5.5
View ArticleForum Post: RE: Drivers installation
Hi Jonathan, See, this post below. Stellaris ICDI + Windows 8 Pro x64 problem-kel
View ArticleForum Post: RE: I2C master always drives SCL low
Hi Wouter, See, reply by cb1 regarding configuring I2C SCL pin using GPIOPinTypeI2CSCL(), from the post link below. I2C Problem - Stellaris LM4F120H5QR-kel
View ArticleForum Post: RE: Stellaris ICDI drivers installation problem with Windows 7 x64
Yes, thouse are the drivers I attempt to install.Thanks
View ArticleForum Post: RE: TIVA Launchpad Debug Error!
Hi Ashwin, Try my earlier advice, hold reset when using the LM Flash unlock feature. See post below. LM4F120H5QR Stuck in Hibernation Mode Also, try using a different USB cable. If these does...
View ArticleForum Post: RE: Connect a C1100EM to FR5739 Experimenters board to use...
Hi,The SmartRf would need to connect over USB through the UART on the FR5739 Expt. board, its this I would need to interface to SPI. It looks like the dev EVK's(SmartRF04EB/SmartRF05EB) use an 8051 for...
View ArticleForum Post: RE: led 2 not blinking after attempting sample project 'blinking...
The MSP430G2553 is a microcontroller. Presumably the development board being used is the MSP430 Launchpad (MSP-EXP430G2)?I'm afraid you haven't provided a lot of details. Instead of relying on a fairly...
View ArticleForum Post: RE: MSP GANG DLL - Help is needed urgently
Hi Katie,Here is the sample VB.net project, changes made are adding fours files in sub folder Bin:Gang430.dllMSP-Gang.dllGANG430.iniGANG430.h (I don't think we need this header file for VB project, as...
View ArticleClik here to view.
Forum Post: MSP430 for measuring line power?
I want to use an MSP430 in a power meter type application. I found this block diagram in one of the MSP430 brochures:Can someone explain to me how the MSP430 is measuring the current and voltage...
View ArticleForum Post: RE: GPIOAMSEL TM4C123GH6PM
Hi Craig,You are correct. PB5 should be 0x20. There is a error in the datasheet for AMSEL register definition, which will be corrected.RegardsAmit Ashara
View ArticleForum Post: RE: Please help. Can't install Tiva. I only see 1 device in...
Hi Vishnu, it appears there was a problem with one of the files in Windows. The following steps solved the issue. Let me know if it worked for you as well.1) Go to the directory...
View ArticleForum Post: RE: Error code #10099-D on CCS5.1
Thanks a lot !!!!II just change another cmd file and it works~
View ArticleForum Post: RE: PWM Duty Cycle Problem
Hi Kyle,Which controller are you using? There seems be some initialization problems in your code.Regards,Gautam
View ArticleForum Post: RE: ControlSuite Update fails
Here are my updater file and ini file. Try replacing them.(Please visit the site to view this file)Regards,Gautam
View ArticleForum Post: RE: Problem running correct C code on TMS320F28335 eZdsp
Alaa, did the pdf help you? Also check these out:https://www.youtube.com/results?search_query=simulink%20ccs%20c2000&sm=3Regards,Gautam
View ArticleForum Post: RE: What does @7 mean in this assembly code?
Hi Robert,Here @7 means "content at location 7"; So, in the above case, you're moving the value present at the location 7 to AR0Regards,Gautam
View ArticleForum Post: CLK and ACLK rotation of stepper motor msp430g2452
I created the program using the FOR loop function for clk and aclk wise rotation of stepper motor. i wrote sequence correctly .But the problem,whatever the program in the 1st loop is executed...
View Article