Forum Post: MSPM0G3106-Q1: asking the time base dependency of WWDT
Part Number: MSPM0G3106-Q1 Tool/software: Hello TI expert I have couple of questions regarding the WWDT of M0G series, In TRM chapter 30 "WWDT", it states : -- the time base of WWDT is independent of...
View ArticleForum Post: RE: TMS320F2812: Data verification failed CCS 2.20
Hello again, During my research, i found this document : Flash Programming Solutions for the TMS320F28xxx DSCs It seems that i have to install a plugging Code Composer Studio On-Chip Flash Programmer....
View ArticleForum Post: AM2432: Profinet LWIP and TFTP
Part Number: AM2432 Tool/software: Hi, I am using AM2432 with Profinet from the Industrial SDK 09.02.00.24. I am porting code implemented on an AM2432 project that uses EthernetIP on my project on a...
View ArticleForum Post: LAUNCHXL2-570LC43: Ethernet Transmission and Receiving Between...
Part Number: LAUNCHXL2-570LC43 Other Parts Discussed in Thread: TMS570LC4357 Tool/software: I’m working on a project that involves setting up Ethernet communication between two TMS570LC4357...
View ArticleForum Post: RE: TPS62822: Request to Functional safety FIT value and Failure...
Hi Varun, Thank you for your response. We would like to inquire about how we can obtain the number of gates for the device in question. As this may be considered confidential information, could you...
View ArticleForum Post: RE: AM2432: Profinet PHYs link status
Hi Laxman, thank you for your answer. I confirm that it works. However I read from this thread that the addresses to read are 0x3001FF08 and 0x3001FF0C (and indeed using these works), while on the TRM...
View ArticleForum Post: RE: AM263P4-Q1: Oscillator voltage requirements Vih/Vil
Apologies for the delay, What we currently have specified in the Digital and Analog IO characteristics table of the device datasheet is all the information I currently I have on the XTAL pads. I have...
View ArticleForum Post: RE: AM2632: Systick interrupt stops.
I apologize for the lack of response here, I will be looking into the interrupt controllers today as well as the RTI registers to make sure there isn't a mask I have missed, as well as reaching out to...
View ArticleForum Post: TMS320F2800157: When all the RAM areas are allocated to Z1...
Part Number: TMS320F2800157 Tool/software: As shown in the figure, all areas are encrypted. When the self-written BOOT is transmitted using SCI BOOT, the code will not run.I want to know how to solve...
View ArticleForum Post: RE: MSPM0C1104: Secondary BSL doesn't work(I2C, UART)
Hi Ryan, Sorry for the late reply, duo to my holiday. I don't know if you have fixed this issue or not? Bas on your in input, I found that you have got the flash write error as below 0xF0 As you can...
View ArticleForum Post: RE: AM2432: Use (general) ECAPs to generate a clock signal for...
The SDFM is configured to process the NC sampling based on the expected clock frequency (20 MHz). A mismatch between the actual clock frequency and the configured frequency can lead to inaccuracies in...
View ArticleForum Post: RE: AM2634-Q1: Issue Reading Full 7 Bytes from DS1307 RTC Using...
Hi, Based on the feedback please provide the waveform so that we can proceed forward with debug.
View ArticleForum Post: RE: AM263P4: relocation to symbol "__TI_exidx_linkto_scn_start_1"...
Hi Kacper, Apologies this got dropped from our Radar Is this issue still open?
View ArticleForum Post: RE: MSPM0L1106: Is the ROM BSL I2C0 supported on the 16-pin parts...
Hi Derek, I had quite a number of our HW and SW engineers involved on this one and the conclusion is: Add the plugin interface in Flash with NRST Pin disabled in BSL_PI_I2C_init(). See attached....
View ArticleForum Post: TMS320F28379D: Gui Composer OS Windows 11
Part Number: TMS320F28379D Other Parts Discussed in Thread: LAUNCHXL-F28379D Tool/software: Dear, I have new configuration (Windows 11 and new PC) . I have installed ode Composer V20, Ticloudagent and...
View ArticleForum Post: RE: TMS320F28379D: CCS v20.1.1 - how to remove annoying...
I found out the setting that enables or disables the text Inlay hints -> off It is a part of text editor settings
View ArticleForum Post: RE: TMS320F28P650DK: SysConfig CMD tool. Warning: memcfg module...
Hi Sebastian, I am able to reproduce the warning messages that you have. Let me discuss with the tool experts and shall get you back. On the 3rd point, currently we are having predefined the FLASH and...
View ArticleForum Post: RE: AM2634: how to call 2nd times for...
Nilabh, After upgrading the APP online, I want to verify the APP data written to FLASH and then reply whether the written APP is available. Currently, after calling Bootloader_parseMultiCoreAppImage,...
View ArticleForum Post: MSPM0G3519: LIN slave Wakeup support in LIN UART
Part Number: MSPM0G3519 Tool/software: How to configure the UART module to detect LIN wakeup signal in LIN slave configuration? In Reference Manual of MSPMO G series not seen UART Register...
View ArticleForum Post: RE: AM2632: GPIO Interrupt and related GPIO INT XBAR configuration
Hi Nikhil, Thanks for sharing the material link and explanation. With Sysconfig the configurations are tried for GPIO Bank Interrupt as suggested in Forum by Nikhil and its working . But w.r.t. Using...
View Article