Forum Post: RE: MSPM0C1104: What is the size of the Emulated EEPROM provided...
Thank you for the reply, Since we have 2 sector totally 2KB of EEPROM Emulation is allocated i'm right.
View ArticleForum Post: RE: AM2634: AM2634 Ethernet Individual MAC mode
hi Brennan, Can't my requirement be achieved using CPSW, I need to use ethernet in RMII mode. whereas the suggested solution by you is only possible with MII interface. If so, please provide resources...
View ArticleForum Post: MSP430FR6043:...
Part Number: MSP430FR6043 Tool/software: Hello, We are facing a issue with USS module particularly with USS Crystal. Please refer the below image for USS error code. # The USS crystal we verified...
View ArticleForum Post: RE: TMS320F28P550SJ: CCS flash programming problem
Yes, the newer version works, thanks again! Jouko
View ArticleForum Post: RE: LP-AM243: Run the uart_uniflash.py python script
Hi Holger, Are you using a TI EVM or a custom board?
View ArticleForum Post: RE: TMS320F28P659DH-Q1: MCAN TX buffer questions
Hi Fleenor, Thanks for your information. Customer is still waiting for response and need your help to check it. Best Regards Kita
View ArticleForum Post: RE: MSP430FR6922: [Urgent] UART Communication Freeze on...
Hi Gray Gao, Thanks for your questions. Please see our responses below: Fail Rate: Currently, the failure rate is around 2 0% . Reproducibility After Power Reset: After a power reset, the issue does...
View ArticleForum Post: RE: TMS320F28379D: I2C EEPROM Programming ACK Problem
Hi Aishwarya, We have checked hardware and noticed that SDA and SCL lines are crossed. We corrected out mistake and problem is resolved. Thank you for your answer. Best Regards
View ArticleForum Post: RE: TMS320F28388D: EMIF data write issue
Yes, we have received new set of boards. Tested in that and we are able to read & write to FPGA properly. Thanks for the support.
View ArticleForum Post: RE: TMS320F28379D: LAUNCHXL-F28379D
OK i will try CANOpen stacks from the 4Ps recommended by TI. Also I was able to stop retransmission in loopback interrupt example by setting the DAR bit .
View ArticleForum Post: RE: AM2434: Request to Functional safety FIT value(SN29500-2) and...
Hi, Please create separate threads for asking questions related to different device for example, put sitara microprocessors in one thread and similar for other device category. Thanks, Shreyansh
View ArticleForum Post: RE: TMS320F28379D: Interrupt configured in CPU1 not being...
Hi Raghavendra, If you are servicing the ISR from CPU2, then CPU2 will need permissions for the ePWM1. In most ISRs, the peripheral registers are accessed which as well you would not be able to do if...
View ArticleForum Post: RE: TMS320F280039C: Using eCAP Block in HRCAP Mode to Capture...
First: 1. I change Hardware Board = TI F28003x 2. Follow the same setup for Hardware Setting in the example. 3. Here are setting for eCAP3(HR) 4. I was able to use normal eCAP 1,2 but eCAP3(HR) are...
View ArticleForum Post: LAUNCHXL-F280049C: F280049C Luanchpad Unable to interface with...
Part Number: LAUNCHXL-F280049C Tool/software: I have been trying to integrate SPISD module using FATFs and SDISP interface libraries.. some how it is not working. I am a beginner, and I kindly request...
View ArticleForum Post: RE: TMS320F28069: TMS320F28069
Hi Sandy, The maximum frequency is equal to SYSCLK (which for F2806x is 100MHz). This would be if you set the period to be every 1 SYSCLK and prescaler to divide SYSCLK by 1. Best Regards, Delaney
View ArticleForum Post: RE: TMS320F28379D: LAUNCHXL-F28379D
Ok I will try SIMMA SOFTWARE stacks for CANOpen .
View ArticleForum Post: RE: TMS320F280039C: How to get the reason when chip run into ITRAP
Hi Shuqing, Let me loop in the expert who helped on the other thread to see if they can answer your questions. Best Regards, Delaney
View ArticleForum Post: TIDM-HV-1PH-DCAC: Reference design enquiry for our requirements...
Part Number: TIDM-HV-1PH-DCAC Tool/software: Hi sir, I reviewed TIDM-HV-1PH-DCAC document and we want to design 5KVA single phase inverter with 48Vdc input and we require pure sign wave output. Does...
View ArticleForum Post: RE: F29H85X-SOM-EVM: RTINT on F29H85x
Hi The firmware compiles. You have to use the FLASH configuration. I tried the firmware on 3 different PCs and it compiles on each. please try again
View ArticleForum Post: LAUNCHXL-F280039C: issue the connects to the target
Part Number: LAUNCHXL-F280039C Tool/software: Dear TI Support team I have purchased the LAUNCHXL-F280039C board (2 no.), but neither connects to the target (which means I cannot program from CCS). I...
View Article