Forum Post: RE: TMS320F2800156-Q1: Flash Image via SCI-boot mode
Hello, Please see Serial Flash Programming of C2000 Microcontrollers (Rev. H) section 3. The ROM bootloader expects the .txt file to be generated using the following post build step: "${CG_TOOL_HEX}"...
View ArticleForum Post: RE: TMS320F28335: SCI communication signal active level is low....
Hello Sheldon, There is no polarity bit in the SCI registers. Can you show what waveform you see and how it differs from the expected data format? Are you running your own program on the device? Could...
View ArticleForum Post: RE: TMS320F2800137: How to use sprintf in F2800137 with limited...
Hi Jim, Thanks for the reply! Please allow another day for me to check with another team member on suggestions here. Best Regards, Allison
View ArticleForum Post: RE: TMS320F28377D: Data visualization tool for C2000
I did, it is not helping.
View ArticleForum Post: RE: TMS320F28377D: Letter of Volatility Request
I am not seeing where this is duplicated. Can you provide a link to show where it has been?
View ArticleForum Post: RE: TMS320F28377D: Letter of Volatility Request
Nevermind. I found where someone posted the letter and just took it.
View ArticleForum Post: RE: TMS320F28388D: JTAG flashing with UNIFlash resulting in Error...
Hi, Which version of CCS are you using? Do you have another debug probe that you could try? Thanks, Ben Collier
View ArticleForum Post: RE: TMS320F28388D: JTAG issue - can't connect to target
Ok, I will wait for your update.
View ArticleForum Post: RE: TMS320F2809: TMS320F2809PZS AND TMS320F28F28377DPTPEP...
Hi Matthew, can you point me to where you see these EOL timelines?
View ArticleForum Post: RE: TMS320F280039C-Q1: Some question about CLA_STL
Do they have interrupts enabled for some of their CLA tasks (i.e. what interrupts are enabled in PIEIER11)? Which bit in PIEIFR is set that is causing the value of 0x80 to be reported. Is it set...
View ArticleForum Post: RE: MSP430F1491: Release Binary Packaging Guidance
Thank you for this. Just so you're aware for future questions, the customer believes they found the problem. It appears to be due to the 200mV POR issue. The recommended resistor values for the...
View ArticleForum Post: RE: TMS320F28379D: Issue with Dual-Core Configuration and GSRAM...
Hi, I think it's just telling that you need to assign CPU2 as controller for that RAM. Are you facing any issue while using this RAM from CPU2 ? Regards, Vivek Singh
View ArticleForum Post: RE: TMS320F28335: XINTF
Have you checked the proper connection of data and address but on the board ? Are you able to see the data bus properly toggling with correct data ?
View ArticleForum Post: MSP-GANG: Error 23, 33 occurs while using the MSP430FR5968
Part Number: MSP-GANG Other Parts Discussed in Thread: MSP-FET Tool/software: Hi experts, My customer has created a board using FR5968, but there are cases where it cannot be written from MSP-GANG. Q:...
View ArticleForum Post: RE: CCSTUDIO3: CCS Scripting example
Here are a couple of newer links for documentation: https://software-dl.ti.com/ccs/esd/documents/users_guide_ccs/index.html...
View ArticleForum Post: RE: SM320F2808-EP: IDE/Project setup
Steve, Some of those old C28x examples specify that they have a dependency on XDAIS. They actually do not need it. You can edit the project to remove the dependency. Here is a thread with some...
View ArticleForum Post: RE: TMS320F28377D: Data visualization tool for C2000
Hi Bharath, For the following post steps, did you make sure to update to your path? Apologize, I had not mentioned to update these since I am using ccs2010. Seems like you're using ccs2011? if not...
View ArticleForum Post: MSPM0G1506: BOR settings are not reflected
Part Number: MSPM0G1506 Other Parts Discussed in Thread: SYSCONFIG , Tool/software: Hello. I have a question about the BOR settings. I have set the BOR threshold level to 1 for the MSPM0G1506 in...
View ArticleForum Post: RE: LP-AM243: ipc_rpmsg does not work correctly after restarting...
Hello Carrillo-san, Thanks for your reply. I did not write enough. Sorry for that. The base address and size of the vring buffer are the same because (2) and (3) share the same source file output by...
View Article