Forum Post: MCU-PLUS-SDK-AM243X: AM243x
Part Number: MCU-PLUS-SDK-AM243X Tool/software: Hi I am using AM243x for EtherCAT controlled motor control drive. 1. I am using a PRU for SDFM in which it is configured that sync out of PWM0 is the...
View ArticleForum Post: RE: TMS320F28069: TMS320F28069:
Hi Jayanthi, Unfortunately, we do not have any support for Labview files inside CCS. Thanks, Ricky
View ArticleForum Post: RE: TMS320F28377D: Inverter code
Hi Sumit, Apologize but this is not TI generated content. We have C28x academy that you can use, and our SDK to learn more about our F28377D devices. Here is our device product link:...
View ArticleForum Post: RE: TM4C129ENCPDT: JTAG programming TM4C failed with corrupted...
Hi Hong, [quote userid="542779"...
View ArticleForum Post: RE: AM263P4-Q1: Error in writing values to L2OCRAM_BANK4...
Just a an update, I tried changing the memories configuration around so the shared memory is in 0x70080000 with size of 512KB so memory bank 1, and core 1 OCRAM now is in bank 4. Now the array is...
View ArticleForum Post: RE: TMS320F2800137: Setting GPIO pin as output pulls down nSLEEP...
Hi, [quote userid="632656"...
View ArticleForum Post: RE: TMS320F28377D: I would like to know whether handling ADC...
Sang-il, As we discussed before, the ADC calibration values should be called with CPU1. This can be tested by trying to use AdcSetMode() function with CPU2 which cannot write the call the right trim...
View ArticleForum Post: RE: TMS320F2800137: Setting GPIO pin as output pulls down nSLEEP...
Hi, Maybe I was not clear in my description. I am debugging F2800137 CPU, which is supplied by LDO from DRV8317 IC. This driver IC has nSLEEP pin which needs to be at level 1 in order for LDO to work....
View ArticleForum Post: RE: TMS320F28377D: Letter of Volatility Request
This post has been duplicated. Let's continue on the original post. Best, Ryan Ma
View ArticleForum Post: RE: TMS320F2800137: Setting GPIO pin as output pulls down nSLEEP...
I have already post this to DRV8317 forum and they redirect me to C2000 forum. Maybe setting pin which has some voltage on it to output mode triggers pulling down the pin somehow?
View ArticleForum Post: RE: TMS320F2800137: Setting GPIO pin as output pulls down nSLEEP...
Why I am trying to control nSLEEP pin from F2800137 is because short pulse (less then 50us) on this pin resets fault condition state inside DRV8317 and does not put IC to sleep mode.
View ArticleForum Post: RE: TMDSCNCD28379D: How to choose the right ADC interrupts?
Hello Hongmei, As we talked about earlier, it's really up to you to figure out what suits your application best, and all interrupts can be useful for you. Let’s go through an example of how to pick...
View ArticleForum Post: RE: LAUNCHXL-F28379D: RMS Value calculation
Hello, Here you can download our motor control SDK: https://www.ti.com/tool/C2000WARE-MOTORCONTROL-SDK You can find the universal motor control from following path: {install...
View ArticleForum Post: RE: TMS320F280045: Regarding the issue of using C2000-GANG for...
Do you know what address the verification failure occurs?
View ArticleForum Post: RE: TMS320F28377S: How to enable Flash Protection for code Locking
if you reset the device and flash boot is enabled the debugger won't be able to connect. If you are testing with a debugger connected can you use wait boot instead?
View ArticleForum Post: RE: TMS320F28388D: Error #10008-D Error #10010 when building core...
Resolved. File points to ccs v1200 while using ccsv1240
View ArticleForum Post: RE: TMS320F280039-Q1: How to judge if DCSM is enable or isn't enable
Hey Shuqing, I will close this thread since we resolved this issue over webex
View ArticleForum Post: RE: LAUNCHXL-F28379D: J19/J20 Differential Amplifier
Hi Onur, You'll need to both scale and offset you signal to the range of 0-3.3V. Best Regards, Masoud
View ArticleForum Post: AM263P4: Can XBAR be used to map ADC0_EVT1 to PRU_0 interrupt.
Part Number: AM263P4 Other Parts Discussed in Thread: SYSCONFIG Tool/software: I am looking to use the XBAR to trigger an interrupt on PRU_0 when ADC0 has Interrupt 1 trigger. I am trying to do this...
View ArticleForum Post: RE: TMS320F28379D: "Loading error " for Customized board with...
Hi, I merged your two threads together since they discuss the same topic. [quote userid="648842"...
View Article