Forum Post: RE: SYSCONFIG: Incorrect RTI4 Clock Source register on AM263P4 part
I am currently running MCU+ SDK for AM263Px version 10.1.0.31. You can see from the file that I have an RTI instance set to use RTI4 with a clock source of SYS_CLK. When this generates code, the...
View ArticleForum Post: AM2632: About AM263x boot mode design & peripheral pin
Part Number: AM2632 Tool/software: HI Team, How to understand disconnecting boot state latch vs. functional operation if peripheral pin use? Because the PCB size limit, my customer want to connect...
View ArticleForum Post: RE: EK-TM4C1294XL: EK-TM4C1294XL
Hi, Although lwIP can support socket-based API, we don't have any examples. All Ethernet examples we have are only using RAW-style APIs, sorry. Please note that lwIP socket style implementation...
View ArticleForum Post: RE: TMS570LS1224: Consideration of ISO 26262-5:2018 Requirements...
I'm sorry, this does not help me. The ISO 26262-5 requirements i posted above specify, that not one single point fault or residual fault (of each of the failure modes) is allowed to exceed one-tenth...
View ArticleForum Post: TMS320F28027: angle compensation
Part Number: TMS320F28027 Other Parts Discussed in Thread: MOTORWARE Tool/software:...
View ArticleForum Post: TMS320F28027: Dynamic maximum current
Part Number: TMS320F28027 Other Parts Discussed in Thread: MOTORWARE Tool/software:...
View ArticleForum Post: RE: MSPM0G3507: Cant clone project
Are we using different tools? You seem to have 9 projects inside "Folder". I do not see how to do that. For me a "Folder" === "Project". I have multiple folders/projects under one workspace. If you...
View ArticleForum Post: RE: LAUNCHXL-F280039C: CanFd bus off
Hi, Could you check the contents of MCAN_ECR register to see which errors are accumulating before CAN bus goes into bus off condition? I have not encountered any bus off condition when using...
View ArticleForum Post: RE: MSPM0G3507: Cant clone project
There is _no_ documentation support here for what you have shown in your picture. https://software-dl.ti.com/ccs/esd/documents/users_guide/ccs_project-management.html#workspaces " a workspace is a...
View ArticleForum Post: RE: TMS320F28P659DK-Q1: Question About MPOST_EN Bit in...
Mario, There are 2 different memory regions in play here. The Z1-DIAG, is contained in OTP memory, and is what is used to enable MPOST in a customer system. The Z1_DIAG register, is meant to hold the...
View ArticleForum Post: RE: TMS320F28388D: MPOST - Memory power on test
Chao, I don't have the run time of the MPOST at the moment. My feedback was that if you are seeing PBIST_MEMORY_TEST_PASS when you main code takes over from the BROM, it will indicate that the MPOST...
View ArticleForum Post: AM2632: RBL log contains errors in case of booting SBL from...
Part Number: AM2632 Tool/software: Hello, I had already some correspondance with the TI forum, concerning the RBL log data of AM263x: e2e.ti.com We use QSPI with external flash in our custom board....
View ArticleForum Post: RE: UC1524A:UC1524AJ
Good morning, The page indicates that it's an active product, but I don't see it in stock. When will 20 units be available? Please, confirm me
View ArticleForum Post: RE: TM4C123GH6PZ: LATCH-UP AND FREEZING OF MICRO DURING ESD
Hi, As much as I wanted to provide guidance, you are testing the MCU beyond its ESD rating which is out of spec. You need to add ESD protection around the MCU so any ESD events reaching the MCU does...
View ArticleForum Post: RE: AM2632: RBL log contains errors in case of booting SBL from...
Hi Jo, Please note that we have an errata on AM263x for HSSE device(secure device) For redundant boot.
View ArticleForum Post: RE: TMS320F28P659DK-Q1: MCAN Register Offset Discrepancy
Hi Ryan, The register offsets in the TRM are represented in the smallest C2000 (C28x) byte size, which is 16-bit wide. This can be a bit confusing since a normal bye is 8 bits wide. MCAN registers are...
View ArticleForum Post: RE: AM2434: Software reset
Hello Vaibhav, I'm using QPI mode to enable 4s-4s-4s mode. I tested this setup using the ospi_flash_io example provided by TI and it works correctly. Best Regards, Andrea
View ArticleForum Post: RE: AM2632-Q1: Missing symmetric key in HSM Runtime
Hi, now customer has rewritten the HSM RT and all functions have been implemented. The only downside is that they cannot use the salt as it is intended. Regards, Holger
View ArticleForum Post: RE: EK-TM4C1294XL: TM4C1294NCPDT
Hi Charles, Don't worry, I realised you weren’t referring to bl_config when discussing the DHCP and AUTOIP settings. I did find the relevant flags and updated them accordingly. That said, I’m still...
View Article