Forum Post: RE: AM2732: How to improve the transmission speed of 100 Mbps...
HI K.Z , What is the packet rate that you are sending out from AM2732 to external PC? I mean how many packets per sec? Is it a steady/flat rate? Please elaborate more on that- [quote userid="584182"...
View ArticleForum Post: RE: AM2432: Timer Callback without Interrupt
Hello Kevin The user call back support is valid in the Interrupt mode. If the user wants to go with the polling Model, user needs to check whether the timer is overflowing or not. The below example...
View ArticleForum Post: RE: LP-AM243: [LP-AM243] AM2434 Firmware Upgrade Over Ethernet -...
Hi Nitika, My custom board always boots in OSPI mode. Currently, I first connect to the target through CCS and use a GEL script to switch from OSPI to UART mode. Then, I run a Python script via CMD to...
View ArticleForum Post: LAUNCHXL-F28379D: F28379D
Part Number: LAUNCHXL-F28379D Tool/software: Is it possible to use the NRF2401 module for wireless communication using the F28379D?
View ArticleForum Post: RE: AM2432: Power Ramp and Initialization Sequence,CKE has a...
Hi JJD: Thank you for you reply,your test waveform, looks like it just meets the 2ms, but have you expanded the waveform to measure the time between RESET and the rising edge of CKE or 2ms? my lpdd4...
View ArticleForum Post: RE: TMS320F28377D: I would like to know whether handling ADC...
Hello, Thank you for your response. As far as I understand, that in order to meet the ADC specifications presented in the F2837xD's datasheet, the calibration routine included in the AdcSetMode()...
View ArticleForum Post: MSPM0L1117: Is there a DATA Region in the MSPM0L1116.
Part Number: MSPM0L1117 Other Parts Discussed in Thread: MSPM0L1116 Tool/software: Hi All, Does the MSPM0L1116 have a data storage area in Flash? My customer want to save input data when using the...
View ArticleForum Post: RE: MSP430FR6043: Water Meter USS Configurations
Team, Any update on this query?
View ArticleForum Post: RE: MSP430FR5994: MSP430FR5994 SPI ISSUE
Hi Bruce, 1. Switching to UCB0 is probably too late, but I tend to think it's more about the limitations of the MSP430 itself. Interrupts are still a better architectural design for me; the line under...
View ArticleForum Post: LP-AM261: SDK version 10.0.1.10 SBL OSPI example is not working...
Part Number: LP-AM261 Tool/software: SBL OSPI example is not working with SDK version 10.0.1.10. SBL doesn't run.
View ArticleForum Post: RE: MSP430FR5994: MSP430FR5994 SPI ISSUE
Hi David, Subsequently, I will test with a higher-clock MCU. Assigning the 50k SPS sampling rate to the MSP430FR5994 is truly too much of a burden. Thank you very much for your suggestion. Best...
View ArticleForum Post: RE: MSP430FR2355: CCS Theia, really, how bad is this, major step...
Hi Ricky As this is TI I am willing to spend time :-) (I am ex Technical Marketing of National Semi Germany before the take over) and I appreciate that you are taking our experience seriously. We are...
View ArticleForum Post: RE: TMS320F28388D: DMA initialization issue on C2000Ware Ethernet...
Hello, I ran the ethernet_c28x_config binary before the lwIP example, and everything is working correctly. Thank you for your help. Best Regards, Robin
View ArticleForum Post: RE: TMS320F28P550SJ: Where is the corresponding setting in...
Hi Wayne, If you have enabled interrupt in syscfg then you need to call 'MCAN_txBufTransIntrEnable' before adding TX buffer request. regards, Anand
View ArticleForum Post: LP-MSPM0L1306: How to add core command to change UART baud rate...
Part Number: LP-MSPM0L1306 Tool/software: Hello Team, I'm using ROM based BSL demo "bsl_host_mcu_to_mspm0l11xx_l13xx_target_uart". When using ROM based BSL, I understand I can only change...
View ArticleForum Post: RE: LP-AM261: SDK version 10.0.1.10 SBL OSPI example is not...
Hi Joshua, Did you ensure the Boot jumpers are set correctly as shown in: AM261x MCU+ SDK: EVM Setup Further question would be: Are you using CCS 20.0 ? Or CCS12.8 ? Regards, Alex
View ArticleForum Post: RE: LP-AM261: SDK version 10.0.1.10 SBL OSPI example is not...
I am using CCS12.7, boot jumpers are set as per the recommendation. Is there a need to upgrade to CCS 20.0, if yes i would like to understand on the reason behind this update.
View ArticleForum Post: RE: TMS320F28375D: I'm curious about the reason why the ADC...
Dear Masoud Farhadi, Thank you for your response. You mentioned that the 100-pin package doesn't support asynchronous ADC operation. Does this mean the ADC-A and ADC-B modules in the TMS320F28375D...
View ArticleForum Post: RE: LP-AM261: CPSW Examples cant be imported to CCS
Hi Shaunak, The workaround works ok. Regards Daniel
View Article