Forum Post: TMS320F28388S: Facing issue to interface ads131m08 adc chip with...
Part Number: TMS320F28388S Other Parts Discussed in Thread: ADS131M08 , , ADS131M08EVM Tool/software: Facing issue to interface TI ADC chip ADS131m08 with my MICRO TMS320F28388S. Here I am attaching...
View ArticleForum Post: RE: TMS320F280039: Compiler issue (22.6.1.LTS) both on CCS 20 and...
Hi Delaney, the code is as simple as it looks, and it mostly works as intended. Note first that everything in this example is tailored for the execution issue to show up. The loop iterates over the...
View ArticleForum Post: RE: AM2612: API OSPI _readCmd issue
Hi Rijohn, I have read Technical Reference Manual, and it solved my questions.
View ArticleForum Post: RE: AM263P4: Scripts for OSPI flash of AM263PX
Hello Team, Please let me know if you have any update on this topic ? Can we have short debug session to understand more about the issue ? Best Regards, Vishwanatha N
View ArticleForum Post: RE: TMS570LS3137: LWIP FIQ and IRQ Handler
Hi, I have seen these examples before in the forum but this is not exactly my problem. I don't use FreeRTOS and DHCP, I use static IP, I change the configuration of the code running in IRQ to FIQ...
View ArticleForum Post: TMDSCNCD263P: Using VCC_1V8_LDO4 as ADC VREF
Part Number: TMDSCNCD263P Tool/software: Hi, My customer wants to use VCC_1V8_LDO4 as ADC reference on TMDSCNCD263P board. Below is Figure 2-36 in users guide (spruj86c). He set SW7 Pin1-2 position...
View ArticleForum Post: RE: MSP430FR6043: EIC Interrupt missing edges
Hi, Min How do you check GPIO_PIN0_Value, in debug? But compare it with Scope in realtime, I think there maybe some time delay between debugger and Scope. Can you try to set a GPIO output to indicate...
View ArticleForum Post: RE: TMS320F28386D: Differences for f2838x_epwm_defines.h driver...
Dear Madhava, these Macros have not been manually added. They are original Macros of the TI library to configure the EPWM regs. They have been removed in the C2000ware rev 3.0 or latest. Waiting for a...
View ArticleForum Post: EK-TM4C123GXL: This project was created using a version of...
Part Number: EK-TM4C123GXL Tool/software: This project was created using a version of compiler that is not currently install - 18.12.2.LTS [ARM] Always when i try to debug a new project it is this...
View ArticleForum Post: RE: MSPM0G3507: how to create secondary BSL at location...
Thank you so much Zoey, It's work, the interrupt of timer has run!!! And honestly, I still don’t understand why it works! What’s the principle behind this? Here’s what I have: App1 : The only "blue"...
View ArticleForum Post: TMS320F28384S: CHANNEL DATA value incorrectly read from ADC
Part Number: TMS320F28384S Tool/software: Hi All, External CLK uses 16MHz. The ADC and DAC are connected via SPI communication. How do I set up the connection to ADC at 10 MHz and DAC at 40 MHz? Best...
View ArticleForum Post: RE: TMS320F280039: Compiler issue (22.6.1.LTS) both on CCS 20 and...
As a side note, I tested it again with recently released CCS 20.1, which also brings a new firmware for my XDS110 debug probe. The issue is still there, but it seems to be dependent also on the...
View ArticleForum Post: RE: MSP430FR2476: After SoftBOR is generated programmatically, no...
Hi zhou Corrected as follows. "Software POR" is generated programmatically: after reset, no break at any breakpoint after forced break with Pause, stop after restart, ignore breakpoints val_PMMIFG:...
View ArticleForum Post: TMS320F280025: MotorControl SDK - Identification of a ACIM
Part Number: TMS320F280025 Tool/software: Hi, I'm using the universal motor control project inside the MotorControl SDK (5.0.2) and want to identify a ACIM. I have identified a lot of PMSM already,...
View ArticleForum Post: RE: AM2732: How to improve the transmission speed of 100 Mbps...
Hi all, Please answer this question. Best Regards, Ito
View ArticleForum Post: RE: AM2634-Q1: Customer used AM2634 for HSM development issue?
Could you please share your schematics for review? Regards, Nikhil
View ArticleForum Post: RE: MSPM0G3507: how to create secondary BSL at location...
Hi Son, [quote userid="575068"...
View ArticleForum Post: RE: MSPM0G3507: how to create secondary BSL at location...
And please do not enter App2 while CPU in the interrupt handler.
View ArticleForum Post: TMS320F28027F: TMS320F28027 with DRV8301 to run bldc motor
Part Number: TMS320F28027F Other Parts Discussed in Thread: MOTORWARE Tool/software: Hi I am using Project Lab 11 in MotorWare, and I'm encountering some errors in the f28027.cmd file. Could someone...
View ArticleForum Post: RE: TMS320F28021: How to read data and write on other mcu
yes, i am using latest version of CCS and i do have CCXML file for TMS320F28021. what do next? i open CCXML file and test connection. it shows success, after i go to memory for reading, i write main...
View Article
