Forum Post: RE: TM4C1294NCPDT: TM4C1294NCPDT EPI EXTERNAL MEMORY WRITING PROBLEM
Hi, - Where is your RAMFMD mapped to? - Why do you reset g_pui16EPISdram to 0 at line 264? g_pui16EPISdram is supposed to be a pointer to 0x60000000 if your RAMFMD is mapped to this address. You are...
View ArticleForum Post: RE: MSP430FR5989-EP: Pull down cap on RST w/ SBW or no? Short on...
Hi Brian, You are correct. You don't need the pull-down resistor if you don't use the reset behavior. Best Regards, Diego Abad
View ArticleForum Post: RE: TMDSCNCD28379D: How to configure the CLB properly using...
Hi Peter, Yesterday I thought the first relative paths are set by default and didn't realize that it shows "none" in the first Fig.1 but I clicked on it the path shows there in Fig.2. I am not sure if...
View ArticleForum Post: RE: EK-TM4C1294XL: Boosterpack
Hi Matteo, You can find all the open source boosterpacks for TI LaunchPads at https://www.mouser.com/applications/open-source-launchpad-boosterpacks/ .
View ArticleForum Post: RE: TMS320F28P650DK: HRPWM of phase shift only works to MEP step...
Hey Prarthan, I've sent you the project file internally, LMK if you got it and its ok. BR, Nathan
View ArticleForum Post: RE: MSPM0G3507: "Hard Fault" when running images built with the...
Hi Sal, [quote userid="522967"...
View ArticleForum Post: RE: EK-TM4C1294XL: Boosterpack
Hi Matteo, Apparently not but let me find out if this is intentional.
View ArticleForum Post: MSPM0L1304: MSPM0L1304 BSL UART TX contention with VREF+
Part Number: MSPM0L1304 Tool/software: Hi, In the part number MSPM0L1304SRTRR, pin 2 is by default the BootStrap Loader UART TX signal. Before the MSPM0L1304 is programmed, w hen the pin operates as...
View ArticleForum Post: RE: MSP430FR5989-EP: Caps on unused ESIDVCC or no? Short on board...
Hi Brian, Since you are not planning to use the ESI Module and there isn't any special requirements in Table 3-2, I believe you may not need to add a capacitor to ESIDVCC and just connect to the DVCC,...
View ArticleForum Post: RE: MSPM0G3107: Question regarding BSL Flash-Based Plug-In...
Hi Raj, Below is what I suggest step: 1. Using the UART plugin interface, with modifying it to the address you assigned. And try work with hardware invoke to finish the bsl communication and new image...
View ArticleForum Post: RE: TMS320F28379D: TMS320F28379D gets disconnected from CCS...
[quote userid="621965"...
View ArticleForum Post: RE: TMS320F28388D: HLC’s instruction cycles time
Hi Johnny, Are you saying that the CLB HLC consumes C28 CPU cycles? I don't think this is the case. Or are you just saying that the HLC instructions require a specific number of CLB TILE clocks to...
View ArticleForum Post: RE: MSP-FET: FET Pro 430
Hi Takayama, Where you download the software, in the Elprotronic? Can you share the version you are using, I find below download pages: https://content.elprotronic.ca/downloads/FET-LITE-win.zip B.R. Sal
View ArticleForum Post: RE: MSPM0G3507: CCS Theia ctrl-click on function goes to wrong...
Hi Chris, That's an odd behavior. CCS should always erase the .out file when it builds/rebuilds a project. The only way to avoid this will be to move the good .out file and place it back to the debug...
View ArticleForum Post: RE: MSP430FR5970: MSP430 ADC Pin Configuration
Simply, the ADC has a number of counts, for example lets say 255. The reference voltage represents the count of 255. If your voltage divider supplies a voltage of half the reference voltage, you will...
View ArticleForum Post: AM2434: pins esd protection and maximum allowed voltages.
Part Number: AM2434 Tool/software: I'm trying to find answers to the following questions about all signal ( digital and analog ) pins and could not find that specific information in the datasheet....
View ArticleForum Post: RE: LP-MSPM0G3519: Program for only 4-byte with ECC in DATA Flash
Hi Eswaran, Are you using our driverlib APIs to write the data to memory? Or are you manually writing to the registers? You can write to the flash 32 bits at a time without overlapping the data, this...
View ArticleForum Post: RE: TMS320F28379D: Illegal ISR upon RESET
Hi Delaney, I have another problem related to CLA, if you don't mind, please look into this tread. TMS320F28379D: CLA does not get triggered - C2000 microcontrollers forum - C2000 ︎ microcontrollers -...
View ArticleForum Post: RE: MSP-GANG: Differences between Hardware Rev: 1.06 and Rev:...
Hi Ito, Maybe you could use the latest software to see whether it works. Which hardware version has the issues, I can see if I have that version of hardware in my side and do a test. (loading to which...
View Article
