Forum Post: TMS570LC4357: LIN1/SCI1 Idle Line Interrupt
Part Number: TMS570LC4357 Tool/software: I would like to ask if it is possible to generate an idle line interrupt after reception of a packet of data on the LIN1/SC1 module? I saw that I can use SET...
View ArticleForum Post: RE: LAUNCHXL-F28379D: Issue with I2C Communication: F28379D as Slave
Hi TingHsuan, Apologies for the delay. Could you confirm if the C2000 target is only in receiver mode or also transmitter? You'll need the ' I2C_setOwnAddress ' function to set the own address for the...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: Fails 60-80% when writing HS-SE...
Hello Prashant, Thanks for the help to understand the questions here. From what I understand, UART has FIFO size of 64 bytes for both TX and RX. I don't understand why DebugP_scanf cannot handle...
View ArticleForum Post: RE: MSPM0L1306: mspm0l1306
Theia has been folded into CCS: https://www.ti.com/tool/CCSTUDIO#downloads The newest version is 20 and change
View ArticleForum Post: TMS320F280049C: Code to spin a BLDC motor using C2000 & DRV816x
Part Number: TMS320F280049C Other Parts Discussed in Thread: LAUNCHXL-F280049C , DRV8161EVM , DRV8161 Tool/software: Hello, I am using the LAUNCHXL-F280049C with the 100 pin F280049CPZS. I am trying...
View ArticleForum Post: RE: MSPM0G3507: Changing HEX File Format Byte Count to 0x10
Hi Pengfei, Thank you very much for your assistance. The main reason I want to do this is to merge three hex files, but the byte counts of each hex file are different. Therefore, I would like to ask...
View ArticleForum Post: RE: MSP-GANG: Is there a facility to check software such as SUM...
Hi All, My customer only check the "image CRC" in the picture above. We do not check it against our own system. The "image CRC" varies between different versions of the application, despite the SW to...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: SPI DMA fail when transfer large size
Hi Anil, Any update? Expect the issue to be confirm soon. The polled/interrupt mode is currently satisfactory and we're also doing a 2048 bytes dma stress test.
View ArticleForum Post: RE: MSPM0L1306: How do I obtain the correct bin file?
Hi Dennis, I have not tried it on CCS.
View ArticleForum Post: RE: TMS320F2800135: How to pre-program the APP function in flash
Hi Rajeshwary Could you please kindly update this thread? Thanks Joe
View ArticleForum Post: UNIFLASH: Error initializing emulator
Part Number: UNIFLASH Other Parts Discussed in Thread: UCD3138 , Tool/software: I encountered the following error while trying to download my program from my UCD3138 chip using Uniflash software....
View ArticleForum Post: RE: MSPM0G3507: A high-frequency sound is heard while the motor...
Hi Sal, That's right. The product that used the MCU of another company that was in use also uses 1 shunt 1mΩ and operates at the same 20kHz. B.R. Donguk
View ArticleForum Post: RE: TMS320F2800137: Universal Motor Control Project & Lab for...
Yanming, Thanks for your help. Regards, Kien Nguyen
View ArticleForum Post: RE: MSPM0G3507: LIN communication is disconnected midway.
Hi Luke, Timer interrupt is the highest priority and LIN, ADC use default I put the timer interrupt above Lin's priority because the timer interrupt is interrupted by Lin. Regrads, Donguk
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: MULTI GPIOs interrupt initinal failed
Update: When used two same bank gpios interrupt, I found only need enable one of the "Enable Interrupt Configuration". The issue fixed, and I suggest that restrictions should be automatically imposed...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: MULTI GPIOs interrupt initinal failed
Hi Tushar, How do you think about the above suggestion to impose automatic restriction in sysconfig when configure multiple interrupt pin in same bank, to avoid mistake. For example, when configured...
View ArticleForum Post: RE: TMS320F28375D: TMS320F28375D: SCI BOOT Mode (FMSTAT Register...
Alex, Sorry to have kept you waiting. I had accomplished the two things mentioned above. First, Load a different application to the same memory region, it was failed. Second, i debug the kernel over...
View ArticleForum Post: RE: F29H85X-SOM-EVM: INT type interrupt triggers exception.
Zihao, Were you able to resolve the issue? If there are no other questions, I will go ahead and close this thread. Best Regards, Aishwarya
View ArticleForum Post: RE: TMS320F28388D: why are we selecting the slowest possible MDIO...
I have not yet received a response. Could you please provide an update on the status of my queries? If any further information is needed from my side, I would be happy to provide it. Thank you for...
View ArticleForum Post: RE: LP-AM243: How to write XIP image to Flash in SBL processing?
Hello Prashant, Thank you. After reading this guide, I checked the linker command file (linker.cmd) and it was as intended, so there seems to be no problem with the XIP binary I created. However, as I...
View Article