Quantcast
Channel: Microcontrollers
Browsing all 230265 articles
Browse latest View live

Forum Post: EVM430-FR6043: The evaluation board test transducer cannot...

Part Number: EVM430-FR6043 Tool/software: We used EVM430-FR6043 to verify the scheme, and did not see any effective waveforms in USS using 200k and 500k transducers. Even if transducers 1 and 2 were...

View Article


Forum Post: RE: TMS570LS1224: vimEnableInterrupt / vimDisableInterrupt...

Hi Jagadish. I have been working on your suggestions and have implemented the new code below. The main loop executes once, and then the interrupt takes over. On the terminal, the string...

View Article


Forum Post: RE: TMS320F280039C: FSI TDM and daisy chain configuration problem...

Hi Kai, Usually TDM stands for Time-division Multiplexing. It is a signaling mode to by-pass the incoming FSI RX data through the device and out the FSI TX pins without re-transmission. Please refer...

View Article

Forum Post: RE: TMS320F280039C: FSI TDM and daisy chain configuration problem...

Yes, that's right. Please refer to below App note. It shows how to connect TMDSFSIADAPEVM adapter with control card FSI Adapter Board User’s Guide Thanks, Susmitha

View Article

Forum Post: RE: TMS320F280045: Regarding the issue of using C2000-GANG for...

thanks. Have you found the issue? When will the new version be ready for the update?

View Article


Forum Post: RE: MSPM0L1227: aeabi_uidvmod.S was not found

Hi Dylan, Thank you for your reply. Sorry for my short explanation. They're using their own test code, and read 32bit data from arbitrary address in Flash by using pointer. Then, __aeabi_uidiv() is...

View Article

Forum Post: RE: TMS320F28P550SJ: Run the same piece of code on flash - having...

Hi Skyler, Thanks for your help! Please keep me posted. Best Regards, Seamus

View Article

Forum Post: RE: TMS320F280049C: Unable to use FLASH API to enable JTAGLOCK

Sure,

View Article


Forum Post: RE: TMS320F28P650SH: DSP can not run to main function after power...

Hi, I'm not sure where during the flashing stops (if your codestart wasn't stored before disconnect). The bootloader not booting to the flash entry point is understandable. I'll need some more...

View Article


Forum Post: RE: TMS320F280039C: How does the system jump to address 0 to...

Can anyone help me resolve this issue?

View Article

Forum Post: RE: LP-MSPM0L2228: programming issue using J-Link as...

Hi, Daniele If in CCS, using empty project with default .cmd file, there won't be content that need to be loaded into SRAM. But log shows that there are data need to load to 0x20200000 and this is...

View Article

Forum Post: RE: TMS320F2800157: Flash Memory error erasing Bank 0 FMSTAT

Hi Matthew I just had a long holiday, on the new MCU, everything worked normally. I mean, I can't read the flash memory area on the old MCU that has a flash error as you want.

View Article

Forum Post: RE: MSPM0G3507: LIN communication is disconnected midway.

Hi Luke, This means that the communication cable has been changed. The communication cable that was used previously did not receive data after a communication error occurred, but the Lin communication...

View Article


Forum Post: RE: MSPM0G3507: CAN RX gets stuck when multiple messages are...

Hi, Matze [quote userid="353832"...

View Article

Forum Post: RE: MSPM0G3507: A high-frequency sound is heard while the motor...

Hi Akshay, There is no noise occurring at 100us cycles on the 3-phase voltage/current waveform. Could this be a problem with the drv8329 gate driver? The ICs on my controller PCB are MCU, Gatedriver,...

View Article


Forum Post: RE: MCU-PLUS-SDK-AM243X: MSRAM to PruIcss DRAM Communication

[quote userid="634641"...

View Article

Forum Post: LP-AM243: How to use ADC0_AIN as Digital Input

Part Number: LP-AM243 Tool/software: Hi team, I develop sdk of AM243x-LP, I tried to use ADC0_AIN0(GPIO1_80) ~ ADC0_AIN7(GPIO1_87) as Digital Input. In spite of other GPIO are worked, ADC0_AIN are not...

View Article


Forum Post: RE: TMS320F28P550SJ: Configurable Logic Block (CLB) - How do I...

Hello Lori, I used logic analyzer to grab SPI_CLK, TxEn, SOMI and SIMO, and used DATA ID 2 for communication test. The waveform diagram is shown below: Looking at the waveform, my guess yesterday is...

View Article

Forum Post: RE: F29H859TU-Q1: Error: makefile:164: recipe for target...

Yes. It happens with other examples as well.

View Article

Forum Post: RE: LP-AM243: How to write XIP image to Flash in SBL processing?

Hello Prashant, >Have you already tried booting the normal appimage? This comment made me realize that there was a serious mistake. Thank you. It was that I had not assigned the Code and Text...

View Article
Browsing all 230265 articles
Browse latest View live


Latest Images

<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>