Forum Post: RE: SAFETI-HALCOGEN-CSP: Safety Caseis not included in the CSP...
Hi Pratik, This thread seems like duplicate with the below thread: (+) TMS570LS0432: Safety Case is missing in the CSP package. - Arm-based microcontrollers forum - Arm-based microcontrollers - TI E2E...
View ArticleForum Post: RE: LP-AM263P: Not able to select the right Part Number for kit...
Hi Navneet, The Bootmode switch is configured in wrong state. It should be 0010 and in the image shared above it seems to be 1101. Can you please change the bootmode, power cycle and try again....
View ArticleForum Post: TMS320F28027F: INSTASpin FOC
Part Number: TMS320F28027F Other Parts Discussed in Thread: DRV8316 , MCF8329A Tool/software: Dear team, My customer is interested in INSTASpin sensorless FOC of F28027F. I referred below thread and...
View ArticleForum Post: RE: SAFETI-HALCOGEN-CSP: Safety Caseis not included in the CSP...
Hello Jagdish, I made two separate requests. One for the HalCoGen and one for the safeTI diagnostic library.
View ArticleForum Post: RE: AM2434: AM243x-LP
Hi Tushar, no, that page is not enough. I included empty project, where the projects on each has rov file for FreeRTOS ( I updated the path and used absolute path). In a debug session, where one...
View ArticleForum Post: LP-MSPM0G3519: Automotive Rating / AEC-Q100
Part Number: LP-MSPM0G3519 Other Parts Discussed in Thread: MSPM0G3519 Tool/software: Hello, It is planned due rate the uC MSPM0G3519 as "automotive" in the future and passing the AEC-Q100...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: AM243x LaunchPad - Ethernet/IP adapter...
Hi Stefano, then the question is, if you have correctly introduced your own PHY implementation to the Stack or not, the correct way would be: 1) Your PHY implementation should implement the following...
View ArticleForum Post: RE: LAUNCHXL-F280039C: Launchpad debugger not responding
Hi, I applied the methodology described in this post . However, the "fix" goes away when the launchpad is powered off : I reprogramm the XDS110 in the launchpad and am able to program my target MCU,...
View ArticleForum Post: RE: TMS320F28075: Debugging Issue on Custom TMS320F28075 Board –...
Hi, I tried building and executing the gpio_ex2_toggle example from C2000Ware on the TMS320F28075 . However, I encountered the following issues in different execution modes: 1. RAM Mode Issue: When...
View ArticleForum Post: RE: TMS320F280041C: C2000Ware MotorControl SDK 5_03 Lab04 problem
I had a probem with the current measurement, but now everything is fine. But again no turning. I monitored the adc variable and my output voltages and currents are quite low -> 0.05A and 1--2-3...
View ArticleForum Post: RE: TMS320F28375S: CAN Data Not Updating After Jumping from...
Hello, I don't know if there is a glitch or something else but I haven't received a response yet and wanted to kindly inquire if there have been any updates or if additional information is needed from...
View ArticleForum Post: RE: AM2634: Arm-based microcontrollers forum
I'm unable to reproduce this on AM263-LP. Could you read the register SOP_MODE_VALUE in TOP_RCM (Address: 0x53200024) and confirm that it reads 0xB (i.e. Dev-boot mode)?
View ArticleForum Post: RE: TMDSHVMTRINSPIN: Is it possible to tune the output bus...
We have a 6 kW , 128 V PMSM ( 150 V peak ). We need advice on whether we can drive our motor using this kit. Can you give suggestions?
View ArticleForum Post: RE: AM2434: AM243x-LP
Hi Jinglong, Can you please try without changing the path? [quote userid="617178"...
View ArticleForum Post: RE: MSP430FR2475: MSP430FR2476 EVK: Firmware upgrade using BSL...
Hi Gary I am not able to get into BSL mode that i found when i probe the RST and TST signals. The RST always remains HIGH and TST as LOW. Can you please suggest what can be done for RST and TST...
View ArticleForum Post: RE: TMS570LC4357: TMS570LC43 Safety Library
Hi Paul, [quote userid="637553"...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: AM243x LaunchPad - Ethernet/IP adapter...
Yes, the problem is that the function like software reset is not called.
View ArticleForum Post: TMS320F280041C: MotorControl SDK ACIM parameters
Part Number: TMS320F280041C Tool/software: Greetings! I am using conical rotor ACIM with your MotorControl SDK. It seems the motor ID lab(Lab05) is not quite correct with this type of motors. So am...
View ArticleForum Post: RE: MCU-PLUS-SDK-AM243X: AM243x LaunchPad - Ethernet/IP adapter...
Hi Stefano, if no custom PHY drivers are provided in the CUST_PHY_knownImplementation_s then the Stack would look into the known implementation (for example DP83869) internally. Can you confirm if...
View ArticleForum Post: RE: LP-AM243: How to write XIP image to Flash in SBL processing?
Hello, [quote userid="608509"...
View Article
